|Tag Protocol:||EPCglobal UHF Class 1 Gen 2/ISO 18000-6C||Working Frequency:||840～960MHz|
|Communication Interface:||USB、RS232、RS485、Ethernet||Antenna Interface:||Four TNC|
|Reader Chip:||R2000||Dimension:||26.5*25.0*4.5CM(including Bracket)|
|Maximum Operating Current:||1A||Receiving:||-82dBm|
multi tag rfid reader,
fixed uhf rfid reader
Impinj R2000 Long Range UHF Rfid Reader , Rfid Tag Reader For Warehouse Management
1. Employed IMPINJ R2000 RF Chips, up to -82dbm receiving sensitivity and the highest performance in this field makes this module more suitable for harsh application environment.
2. Remarkable performance, can achieve a reading distance over 8m for single tag reading with 8dbi RF antenna.
3. Remarkable performance in intensive taps reading, can attain a tags identification rate of 400tags/s.
4. Provide the most comprehensive functions SDK and ports, easy to integrate RFID software.
5. Adopted integrating RF chip, module performance is more stable, and more suitable for harsh application environment.
6. The use of carrier wave cancellation technology makes the tags reading more accurate and reading scope wider.
7. Provide four TNC antennae interfaces, users can achieve superior reading performance with less equipment deployment.
8. Enhanced noise suppression function for reliable data capturing.
9. High precision return signal strength (RSSI).
|Tag Protocol||EPCglobal UHF Class 1 Gen 2/ISO 18000-6C|
|Supporting Working Area||China, Europe, the United States, South Korea, Japan, Taiwan……|
|Operating Voltage||12V||DC power supply|
|Maximum operating current||1A||Test of transmit power in 30dBm state|
|RF port maximum output power||1W(30dBm)|
|Antenna interface impedance||50Ω|
|Serial communication parameters||Baud rate adjustable(default 115200bps),parity bit:0 ,data bit:8 ,stop bit:1|
|Power output settings||5～30dBm adjustable /Adjustable minimum interval of 1dBm(default 30dBm)|
|High temperature automatic protection function||support|
|Power supply enable||support|
3-Road GPIO can only input can not be input,GPIO port default is low, the output high level of 5V,GPIO 3 IS USDED TO CONTROL LED state indicator(green) and buzzer
Power indicator: Red
|Communication Interface||USB,RS232,RS485,Ethernet||Only one of the communication interfaces on the F5860-H can be used alone. Do not communicate with each other at the same time.|
|Antenna interface||Four TNC||The F5860-H working antenna defaults to antenna 1.Antenna parameters can be configured: working antenna, working time, interval time.|
12V/3A Power Adapter:1
PIN Green Terminal Interface Definition
|3||EN_OUT||Equipment enable control interface,When the high level input, the device will be in a state of sleep.The high level voltage is 5V.|
|4||GPIO1||GPIO port output, can be programmed to control the level of output.The output high level is 5V, the low level is 0V.The maximum output current is 100mA. (The default output level is low level 0V)|
|5||GPIO2||the same as above|
|6||GPIO3||the same as above(note:Equipment has occupied this interface for the green LED lights and buzzer control)|
|7||NC||Reserved interface, no function|
|8||NC||Reserved interface, no function|
|9||WIFI_RESET||Device WIFI configuration parameter reset pin,this pin and the GND pin short to 10 seconds to restore the factory settings WIFI.|
1. OEM Manufacturing welcome: Product, Package...
2. Sample order
3. We will reply you for your inquiry in 24 hours.
4. after sending, we will track the products for you once every two days, until you get the products. When you got the goods, test them, and give me a feedback.If you have any questions about the problem, contact with us, we will offer the solve way for you.